Dinosaur puzzle anatomy and step-by-step assembly instructions


ASSEMBLY STEP ONE: The feet. Our puzzle has two bones labeled "ankle". 

Although this dinosaur did not have a conventional foot like a human and actually has a foot similar to a giant four ton chicken,  we will call this collection of bones the 'ankle' for simplicity.  Insert the toes (called "phalanges") into the bottom of each ankle.  

The slots on the top of the ankle must slant inward with the toes pointed forward. 

Our puzzle has a section of leg connected to each center toe.

The section of leg connected to the center toe is the "metatarsal".  Insert each metatarsal in to each ankle from the top. The left metarsal points forward. 

The right points slightly rearward. Place the assembled feet in the approximate correct position. 


STEP TWO: Legs and knees.  Each leg is separated between the middle leg (called the "tibia") and the metatarsal.  A leg connector is used here. Insert a leg connector into each foot assembly. The slot in the top of each leg connector should slant inward. Insert the left leg (tibia) into the left leg connector. The tibia of the left leg points rearward. Repeat for the right leg. Tibia of the right leg points more or less forward. The upper portion of the leg is the "femur". The slots at the top of each femur should be more or less vertical when assembled correctly.


STEP THREE: The pelvis and hips. The pelvis of Allosaurus has three separate elements; the ilium, ischium and pubis. The pubis is directed forward as in all "saurischian" pelvis dinosaurs.  In our puzzle, the ischium and pubis is already connected and we will install these later These are the parts that look like a pelvic bone. First we need to connect the ilium to the hips. Our puzzle uses two pieces which we will call the horizontal hip plate and the vertical hip plate. Install each ilium into the top of the vertical hip plate  with the long slots in the ilium pointed rearward (see diagram).


STEP FOUR: Horizontal hip plate. The horizontal hip plate has two center slots. One longer than the other. Insert the horizontal hip plate into both ilium (already inserted into the vertical hip plate in step 3).  The longer slot needs to point forward and the neck will eventually be inserted here. As seen from the top, the shorter center slot points rearward.

Horizontal Hip Plate 3D DINOSAUR PUZZLE

STEP FIVE: Hips and legs. At this point you should have both hip plates and both ilium assembled as one unit. Insert the legs into the hip assembly. Remember, the long center slot in the hip plate needs to point forward as seen in step 4. The entire assembly now with the hip plates, both ilium, both legs and feet should more or less stand up as one unit.  It will balance better when we add the neck and tail assemblies later. Set this all aside while we assemble the head.



STEP SIX: The neck plate and upper skull.  Locate the neck plate and the two upper halves of the skull.  Inspect the skull halves.  Generally, one side may look a little cleaner than the other. Orient each upper skull half so the nicest surface is on the outside. Insert each upper skull into the two top slots on the neck plate.

Neck plate and upper skull 3D DINOSAUR PUZZLE

STEP SEVEN: Lower jaws. The lower jaw is known as the "dentary". As with the upper skull, inspect the jaws and determine if one side is cleaner cut than the other. If so, orient the jaws so the nicest sides are on the outside of the model.  Insert each dentary into the lowest slots on the neck plate (see diagram). The head should now be one complete assembly.  For plastic and wood models, a 'jaw connector' is provided to hold the lower jaws together. For steel and aluminum models, the neck plate is manufactured with a slight forward bend in order to force the lower jaws together and the jaw connector is not required.


STEP EIGHT: The Skull. The top of the neck has slots for the "cervical vertebrae" which we will install later. Hold the neck with the slots for the vertebrae pointed upward. Install the now assembled skull and neck plate into the slot at the front of the main long neck piece (the narrow end).  Hold this assembly together in one hand and get ready to install the tail with the other. The legs and hip assembly should be standing near-by. We will need to install the neck/head assembly at the same time that will install the main tail section so the model will remain balanced and standing while we complete installing the rest of the parts.

Neck plate and skull 3D DINOSAUR PUZZLE

STEP NINE: Neck and tail.  The tail has slots on the top for the "caudal vertebra" which we will install later. The lumps on the bottom of the tail represent the "haemal arches".  Balance the legs and hips in front of you. Hold the tail with the slots for the vertebra pointed upward and the haemal arches pointed downward.   With he skull and main neck plate in one hand and the mail tail section in the other, insert both at the same time and the model should remain balanced.

Neck and tail 3D DINOSAUR PUZZLE

STEP TEN: Center rib.  This rib is installed in the center slot in the top of the neck. It is the forth slot when counting from either the front or the rear (center slot).


STEP ELEVEN: The caudal vertebrae.  These are the bones along the top of the tail. Arrange the caudal vertebrae in front of you from largest to smallest then install them on the tail in the same order. Largest bones towards the body, smallest bones towards the tip of the tail.

Tail vertebrae 3D DINOSAUR PUZZLE

STEP TWELVE: The ribs. Our ribs each represent one rib and one dorsal vertebra. Other than the center rib and dorsal vertebra which is already installed, there are three other large ribs. The smallest is inserted in the rearmost slot on the top of the neck (towards the body).  The largest is inserted closest to the center rib.


STEP THIRTEEN: Neck vertebrae. There are 3 parts that look like small ribs. These represent the cervical vertebrae along the top of the neck. Insert the cervical vertebrae in the slots on the top of the neck with the smallest vertebra nearest the neck. Largest nearest the center rib. Now, the arms can be inserted into the center rib. The upper arm (scapula) has one slot. Insert this slot into the outer slot on one side of the center rib. Repeat for the opposite side. The arms are slightly different but will work on either side.

Neck vertebrae 3D DINOSAUR PUZZLE

STEP FOURTEEN: The pelvic bones and key.  This is a little tricky so take a moment to look at the parts to understand how they go together.  The pelvic bones need the 'key' to stay in place. Insert both pelvic bones with the "pubis" or largest bone pointed forward. Hold them BOTH in place and then inset the key into the key slots from the rear.